Agnee Gears - For standard and custom made Worm Gearbox, inline helical geared motor, spur, helical, bevel and worm gears, racks, pinions, chain sprockets, double reuduction worm gearboxes, shaft mounted speed reducer, bevel helical gearboxes,  worm geared motor, planetary reduction gearbox.

Most Trusted Name in Gear Industry for manufacturing standard and custom made Worm Gear Boxes, inline helical geared motor, spur, helical, bevel and worm gears, racks, pinions, chain sprockets, Right Angle speed reduction gear boxes.

Home | Products | About Us | Contact Us | Warranty | Complaint 

HORSE POWER RATING
Agnee Worm Gear Boxes

For Gear Unit selection Prime mover's maximum power rating can be taken as base for determining the actual load. The Gear Selection is made by comparing actual transmitted loads with catalogue ratings. It is important to realise that are based on standard set of load conditions, which invariably change for different conditions. Therefore service factor must be used to calculate a theoratical transmitted load or equivalent load, before comparing with catalogue rating. For calculating the same, apply the formula:-

Equivalent Load = Actual Load x Service Factor

These are some Suggestions to improve the performance of your worm speed reducers, worm gear boxes or worm geared drives. However, please note that these are suggestions based on standard set of conditions. If these are different from your results, please rely on your results and inform us.

Mechanical Service Factor

Prime Mover Duration of Service Hours/Day Uniform

Loads

Moderate

Shocks

Heavy

Shocks

Electric Motor, Steam Engine, or Hydraulic Motor. Under 3

3 to 10

Over 10

0.80

1.00

1.25

1.00

1.25

1.50

1.50

1.75

2.00

Single Cylinder Internal Combustion Engine Under 3

3 to 10

Over 10

1.25

1.50

1.75

1.50

1.75

2.00

2.00

2.25

2.50

Thermal Service Factor

Ambient Temperature
Temp in C

Factor

10

0.87

20

1.00

30

1.16

40

1.35

50

1.62

60

1.97

HORSE POWER RATING

The values below represent the maximum Horse Power Ratings of AGNEE Worm Speed Reducers at service Factor:1

Nominal
Ratio
Input
RPM
Output
RPM
Models
50* 60* 75* 85* 100 125 150 175 200 250 300 350
Maximum Prime Movers Power in Horse Power
5:1 1500
1000
750
300
200
150
2.30
1.80
1.40
3.10
2.50
2.00
6.20
5.00
4.10
10.20
8.20
6.70
13.60
11.10
9.20
20.30
16.30
13.40
35.20
28.00
22.00
49.80
39.00
31.80
63.50
48.00
40.00
87.50
68.00
56.00
114.00
90.00
78.00
158.00
125.00
115.00
10:1

1500
1000
750

150
100
75
1.50
1.20
0.90
2.60
2.00
3.10
3.80
3.10
2.50
6.20
5.10
4.10
8.50
7.20
5.90
14.20
11.80
10.20
21.80
17.10
15.70
30.60
24.00
20.80
40.10
32.00
27.50
72.00
55.00
42.00
98.00
80.00
62.00
132.00
105.00
86.00
15:1 1500
1000
750
100
66.7
50
1.25
0.90
0.70
1.80
1.40
1.10
3.20
2.70
2.10
5.10
4.00
3.20
7.20
5.60
4.20
11.10
8.50
7.00
17.60
13.80
11.80
25.10
19.80
15.20
31.80
26.20
21.60
54.00
42.00
35.00
75.00
50.00
48.00
110.00
90.00
74.00
20:1 1500
1000
750
75
50
37.5
1.10
0.80
0.60
1.50
1.10
0.80
2.90
2.10
1.60
4.30
3.10
2.40
6.20
4.20
3.60
9.80
7.20
5.80
15.70
10.80
8.80
22.90
15.70
13.90
25.80
19.80
16.70
45.00
33.00
26.00
67.00
49.00
39.00
95.00
75.00
60.00
25:1 1500
1000
750
60
40
30
0.85
0.70
0.50
1.25
0.90
0.70
2.40
1.80
1.40
3.90
2.80
2.10
5.10
3.90
3.10
8.20
6.70
5.20
12.50
10.20
8.100
18.50
14.70
11.70
22.10
17.60
14.70
40.00
30.00
23.00
60.00
45.00
34.00
88.00
64.00
52.00
30:1 1500
1000
750
50
33.3
25
0.65
0.55
0.45
1.10
0.80
0.60
2.10
1.60
1.20
3.20
2.50
2.00
4.50
3.50
2.70
7.20
5.90
4.70
10.70
8.20
7.10
16.20
12.10
9.80
19.90
15.60
13.10
34.00
27.00
21.00
53.00
38.00
30.00
75.00
55.00
42.00
40:1 1500
1000
750
37.5
25
18.8
0.40
0.30
0.25
0.90
0.68
0.50
1.80
1.30
0.90
2.50
1.90
1.40
3.60
2.90
2.10
6.30
4.80
3.40
9.20
7.20
5.70
13.20
10.60
8.40
18.00
13.90
10.80
29.00
20.00
16.00
41.00
32.00
24.00
60.00
46.00
35.00
50:1 1500
1000
750
30
20
15
0.30
0.25
0.20
0.70
0.55
0.45
1.40
1.10
0.70
2.10
1.50
1.10

2.90
2.20
1.70

5.10
4.00
3.10

8.10
6.50
5.10
10.30
8.30
7.00
15.80
12.10
8.40
22.00
17.00
14.00
36.00
27.00
20.00
48.00
37.00
30.00
60:1 1500
1000
750
25
16.7
12.5
0.25
0.20
0.18
0.60
0.50
0.40
1.10
0.80
0.60
1.80
1.30
0.90
2.30
1.80
1.30
4.40
3.30
2.40
6.80
5.20
4.10
8.40
7.00
6.10
12.20
9.70
8.10
18.00
14.00
12.00
30.00
22.10
17.00
42.00
34.00
28.00
70:1 1500
1000
750
21.4
14.3
10.7
0.25
0.20
0.15
0.55
0.45
0.35
0.90
0.70
0.56
1.20
1.00
0.80
1.90
1.50
1.20
3.80
2.80
2.20
6.00
4.50
3.70
7.50
6.30
5.30
10.20
8.20
7.10
16.00
13.00
11.00
26.00
20.00
17.00
36.00
29.00
24.00
 
  • The models relate to Centre Distances in millimeter.
  • The Ratios mentioned above are nominal and the actual may vary by upto +10%
  • The Model no. 50 to 85 are available in adaptable Bodies, while 100 to 350 are in Horizontal & Vertical Output Shafts Bodies
  • For overdriven Units, it is necessary to derate by 5% for all the ratios up to 30:1 inclusive and by 15% for 35:1 and higher ratios.
  • Worm Shafts and Worm Gears are also available without bodies.

 


Inline Helical Geared Motor
Inline Helical Geared Motor
Model: M-03 to M-14 Series
Input power: 0.18KW-90KW ;
Transmission ratio: 1.4-250


Horizontal Worm Gearbox

Horizontal Worm Gearbox
Ratio from 5:1 to 4900:1
Center Distances from 40 mm to 400 mm;
Single Stage or Multiple Stage Reduction;
Teeth Size from 1 module


Our Dealers in India | Online Industrial Resources
Helical Gearbox |Adaptable Worm Gearbox | Inline Helical Geared Motor | Racks and Pinions | Pump Jack Helical Gearbox
Shaft Mounted Speed Reducer | Worm Gear Motor | Chain Sprocket | Vertical Worm Gearboxes | Horizontal Worm Gear Boxes
Planetary Gearbox | Double Reduction Worm Gearbox